Our Latest Blog Posts

Power Point Not Working? Common Causes and What to Check

A power point that suddenly stops working is one of the most common calls we get. Most of the time, the cause is simple: a tripped switch, a faulty appliance or a loose connection. Sometimes, though, a dead power point is the first sign of a fault that needs a registered electrician. Here is how to tell the difference, and what you can safely check yourself first.

Electrician Mt Eden switchboard installation by French Electrical

Before you start, one rule: don’t open up a power point or poke anything into it. Every check below is one you can do from the wall or the switchboard without removing a cover. If something needs repairing, leave that to a registered electrician.

First, Check the Power Point or the Appliance

Start with the simplest test. Unplug the appliance and plug in something you know works, such as a phone charger or a lamp. If that works, the problem is the appliance or its cord, not the power point.

If nothing works, check that the switch on the power point is on. Next, try the other outlet on a double power point. If one side works and the other doesn’t, the outlet itself has probably failed.

French Electrical electrician carrying out electrical testing on a commercial switchboard

Power Point Not Working? Check the Switchboard

Most dead power points come down to the switchboard. Open it and look for a switch in the off or middle position. It might be a circuit breaker, which trips when a circuit overloads, or an RCD, which trips when current leaks to earth.

Switch it fully off, then back on. If the power point comes back, unplug everything on that circuit. Then plug things back in one at a time. The one that trips it again is your likely culprit. Our guides on why an RCD keeps tripping and how a circuit breaker works go into more detail.

Why a power point stops working: the usual causes

  • A tripped RCD or circuit breaker. This is the most common cause, and usually the quickest fix. Something on the circuit either overloaded it or leaked current to earth.
  • A faulty appliance. A damaged cord or a failed appliance can trip the circuit every time you plug it in.
  • A loose or burnt connection. Over time, the screws that hold the wires in a power point can work loose. A loose connection heats up, and that heat can scorch the outlet. See our guide to loose outlets.
  • A worn-out power point. Older outlets lose their grip on plugs. As a result, plugs sit loosely, arc and overheat.
  • Water or damage. Outdoor sockets and outlets near sinks can take in moisture, which then trips the RCD.
  • A fault further along the circuit. Power points are usually wired one after another. So a single loose joint can knock out several outlets in a row.

Warning Signs: When to Stop and Call an Electrician

Some signs mean you should stop using the power point straight away and switch off that circuit at the switchboard:

  • A burning smell, or scorch marks around the outlet
  • The power point or plug feels warm or hot
  • Crackling, buzzing or sparks when you plug in
  • The RCD or breaker trips again as soon as you reset it

These all point to a loose connection, overheating or a short circuit. Don’t keep resetting the switch. Instead, leave it off and book a registered electrician.

Scorched socket and damaged appliance lead found during test and tag
Registered electrician checking a switchboard during an electrical safety inspection

How an Electrician Finds the Fault

An electrician starts at the switchboard. First, we test the circuit and check that the RCD and breaker work as they should. Next, we isolate the circuit and open up the dead outlet, and often the outlets either side of it.

Usually, we find a loose terminal, a burnt connection or a failed outlet. We then remake the connections or replace the power point. Finally, we test the whole circuit before switching it back on, so you know it is safe.

When to Replace or Add Power Points

If your home has older power points that are loose, cracked or discoloured, replace them before one fails. Likewise, if you rely on multiboxes and extension leads in every room, you probably need more outlets. Adding power points is safer than overloading the ones you have.

If dead power points and tripping happen often, the real answer may be the switchboard. See our guide to the signs your switchboard needs upgrading.

Burnt out plug top and fuse found during a test and tag inspection

What Sets Us Apart

50+ years of proven electrical experience icon

50+ Years of Proven Experience

Established in Auckland since 1974, French Electrical has been trusted across the region for over 50 years. Our team of registered Master Electricians delivers work that's built to last every time.

After-hours emergency response icon

24/7 Emergency Response

Electrical breakdowns don't keep business hours. French Electrical keeps an electrician on call outside office hours for residential, commercial and industrial clients across Auckland, responding fast to minimise downtime and protect your property.

SiteWise 100 certified badge

SiteWise 100 Certified

French Electrical holds SiteWise 100 certification — New Zealand's highest contractor health and safety rating. This is required by many commercial, industrial and government clients and reflects our commitment to safe worksite practice.

$20,000 workmanship guarantee icon

$20,000 Workmanship Guarantee

As Quality Assured members of Master Electricians, our residential work carries a $20,000 workmanship guarantee. If anything falls short of standard, we put it right — labour and materials — at no cost to you.

If your power point is not working, check the appliance first, then the switchboard. If it still won’t come back, or you notice heat, burning or sparks, leave it off and call a registered electrician. You can check anyone’s licence on the Electrical Workers Registration Board register.

french electrical team

French Electrical has been finding and fixing electrical faults across Auckland since 1974, including after-hours callouts when a board will not stay on. If your power point is not working and the checks above have not solved it, book a job and our team will track down the fault. Landlords can also use our landlord and property manager services. You can see what a callout costs on our pricing page. For general guidance on electrical safety at home, see WorkSafe New Zealand.

French Electrical is an Auckland electrician based in East Tamaki since 1974, covering homes and businesses across East and Central Auckland.